Chevron Left
Zurück zu Pressure, Force, Motion, and Humidity Sensors

Bewertung und Feedback des Lernenden für Pressure, Force, Motion, and Humidity Sensors von University of Colorado Boulder

4.7
Sterne
219 Bewertungen

Über den Kurs

"Pressure, Force, Motion, and Humidity Sensors" can also be taken for academic credit as ECEA 5342, part of CU Boulder’s Master of Science in Electrical Engineering degree. This is our third course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This third course assumes that you already know how to use the kit. After taking this course, you will be able to: ● Understand how to specify the proper AC or DC motor for a machine design. ● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed. ● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software. ● Add a motor and motor control circuit into a microprocessor based development kit. ● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation. After taking this course, you will be able to: ● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data. ● Implement these sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now. You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere. Digikey Part numbers are typed out here: 428-3390-ND CF14JT22K0CT-ND CF14JT100KCT-ND Table shown here: Index Quantity Part Number Description 1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT 2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL 3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL Sparkfun part numbers are typed out here: TAL221 Table shown here: Index Quantity Part Number Description 1 1 TAL221 Mini-load cell - 100g, straight bar Additional equipment needed: • Wire - various gauges and lengths • Breadboard • Oscilloscope – suggested models are: o PICOSCOPE 2204A-D2 available on www.digikey.com or o Digilent 410-324 | OpenScope MZ available on www.newark.com Depending on your budget, you can also investigate these models: o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7 o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661...

Top-Bewertungen

BJ

14. Aug. 2022

Great introduction course to sensors. I really enjoyed the instructors videos as they were clear and engaging. I would recommend it.

TH

27. Aug. 2020

This course is very interesting. I completed this course.But I can not get my certificate.Please help me to earn my certificate.

Filtern nach:

1 - 25 von 48 Bewertungen für Pressure, Force, Motion, and Humidity Sensors

von JiaJie, X

15. Juli 2020

von Paul P

9. Apr. 2020

von Pablo C S

12. Nov. 2019

von HET V B

28. Juli 2020

von Amit A

5. Juli 2020

von Vinsensius C F

1. Mai 2020

von Enrique V

29. Mai 2020

von MR. V S

12. Mai 2020

von Abhishek K

10. Mai 2020

von Mr.KAUSTUBH K S

21. Apr. 2020

von Bonifasius B S A

16. Mai 2020

von Ngo T D

4. März 2021

von Guillaume V

3. Apr. 2020

von Brittany j

15. Aug. 2022

von Theint Z H

28. Aug. 2020

von Kasuntha M

11. Nov. 2020

von Sachin G

3. Nov. 2020

von Nimisha M

23. Dez. 2020

von KARIMULLA S

3. Aug. 2020

von Pankaj R

20. Sep. 2022

von Ganesh R P

23. Juni 2020

von Neredikomma S R

12. Juni 2020

von Yared B

28. Jan. 2021

von Jos� R

2. Aug. 2020

von P S K R

12. Juni 2020