Chevron Left
Zurück zu Sensor Manufacturing and Process Control

Bewertung und Feedback des Lernenden für Sensor Manufacturing and Process Control von University of Colorado Boulder

228 Bewertungen
47 Bewertungen

Über den Kurs

"Sensor Manufacturing and Process Control" can also be taken for academic credit as ECEA 5343, part of CU Boulder’s Master of Science in Electrical Engineering degree. This is our fourth course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled "Sensors and Sensor Circuits", our second course entitled "Motor and Motor Control Circuits", and our third course entitled "Pressure, Force, Motion, and Humidity Sensors". Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. Our second and third courses give you three hands-on lab experiments using the kit. This third course assumes that you already know how to use the kit. You will learn about sensor signal characterization and manufacturing techniques and how to optimize the accuracy of sensors. You will also learn about more advanced sensors, proportional-integral-derivative (PID) control, and how this method is used to give you a closed loop sensor feedback system. After taking this course, you will be able to: ● Understand how sensor manufacturers characterize and calibrate their sensors. ● Tune a PID control loop and access the PID control function of the Cypress PSoC development kit for a motor control application. ● Understand manufacturing methods used to build electro-mechanical and micro-machined sensors. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Or, you may obtain the specs from the site, and purchase them elsewhere. All are quantity one except for N107-ND where you need three, and 493-15371-ND where you need two. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND 493-15371-ND Additional equipment needed: • Wire - various gauges and lengths • Breadboard • Oscilloscope – suggested models are: o PICOSCOPE 2204A-D2 available on or o Digilent 410-324 | OpenScope MZ available on Depending on your budget, you can also investigate these models: o Hantek HT6022BE20MHz - o SainSmart DSO212 - o PoScope Mega50 USB - o ADALM2000 -



15. Nov. 2020

Great course to learn about\n\nSensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.


12. Apr. 2021

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome

Filtern nach:

1 - 25 von 49 Bewertungen für Sensor Manufacturing and Process Control

von Guillaume V

17. Mai 2020

I have learned a lot with this sensor specialization. Some selected application notes part from the reading material are very worth the time spent. The view is broad, sensor circuits, MEMS manufacturing techniques, etc. It helps me progress, better understand what I have seen in my career so far in the aerospace, electrical and medical industries.

von G . p

6. Juni 2020

This video session is very useful to learn both theoretical and practical

von Bhargav c

28. Juli 2020

good one


13. Okt. 2020


von Ngo T D

13. März 2021

Great course, great content and learning material. It has real lab exercises with careful instructions. You can still do the assignment without real circuit, but learning by doing will be more efficient, and of course this subject needs real equipment.

The quiz is really helpful for each module lesson, but some of them are a bit difficult or having typing problem. Teachers should acknowledge and correct that. I hope lecture videos can have more animations about how devices work.


19. Okt. 2020

Excellent Class and i learned more from here

von Nithis r k

21. Sep. 2020

It's very useful

von Samriddhi V K

24. Mai 2020

please increase the contents...Descriptions in presentation slides are not enough well to get clear understanding though we went through the referred text books and links

von Himanshu G

1. Juni 2020

It was good.

von Parishi N

16. Apr. 2020

some concepts in the first 2 weeks were not quite well explained

von Sheikh A M

2. Juli 2020

Instruction was not clear.

von Kasuntha M

16. Nov. 2020

Great course to learn about

Sensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.

von Geoffrey S Q

13. Apr. 2021

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome


21. Aug. 2020

excellent ,we need more practice while solving the problem. material is very useful to answer the questions

von kishan n c

25. Sep. 2020

have got a lot idea about industrial sensors and protocols and their construction theory

von Ashab U

17. März 2021

This course is very effective for practical process control and instrumentation

von Elphus M

23. Apr. 2021

i find it to be life changing course, it is ery interesting


von Mykhaylo S

21. Mai 2022

Excellent and interesting course for Process Control learners

von Dean R

17. Nov. 2019

Great course, well done. Lots of good information here

von Enrique V

20. Juni 2020

This was the best course, I like the Labs :)

von Dr.Krushnasamy V S

4. Juli 2020

very toughest course.

But able to learn lot

von Adetifa O O

6. Dez. 2020

Great course, now I know more on sensors


18. Okt. 2020

ക്ലാസ് വ്യത്യാസപ്പെട്ടിരിക്കുന്നു

von Abelardo J R B

18. Aug. 2021

Excelente , todo muy dinámico.

von Likhith B N

21. Sep. 2021